Indesit Oven BIM 31 KA B IX GB User Manual

Operating Instructions  
OVEN  
Contents  
GB  
Installation, 2  
Positioning  
GB  
English, 1  
Electrical connections, 3  
Data plate  
Description of the appliance, 4  
Overall view  
Control panel  
Start-up and use, 5  
Starting the oven  
Cooking modes, 6-7  
Cooking modes  
Practical cooking advice  
Cooking advice table  
FIM 31 K.A IX GB  
FIM 31 K.A GB  
The electronic cooking programmer, 8  
Precautions and tips, 9  
General safety  
Disposal  
FIM 33 K.A IX GB  
FIM 33 K.A GB  
Respecting and conserving the environment  
BIM 31 K.A B IX GB  
Maintenance and care, 10  
Switching the appliance off  
Cleaning the appliance  
Cleaning the oven door  
Replacing the light bulb  
Guarantee, 11  
Assistance, 12  
08448 24 24 24  
Please phone us on  
 
guarantee  
to activate your  
Electrical connection  
coloured Red. Connect Blue wire to terminal marked  
“N” or coloured Black. If a 13 amp plug (BS 1363) is  
used it must be fitted with a 13 amp fuse.  
A 15 amp plug must be protected by a 15 amp fuse,  
either in the plug or adaptor or at the distribution  
board.If you are in any doubt about the electrical  
supply to your machine, consult a qualified electrician  
before use.  
GB  
! Ovens with a three-pole power supply cable are  
designed to operate with alternated current at the  
supply frequency and voltage indicated on the data  
plate (at the bottom of the oven dashboard). The  
earthing conductor of the cable is the yellow-green  
conductor.  
Two types of connection are provided:  
Connection n° 1  
How to connect an alternative plug  
The wires in this mains  
lead are coloured in  
GREEN &  
YELLOW  
Connecting the power supply cable to the mains.  
accordance with the  
following code:  
13 amp fuse  
Fit a normalized plug to the cable, which corresponds  
to the load indicated on the data plate; if the cooker is  
connected directly to the mains, an omnipolar circuit-  
breaker with a minimum opening of 3 mm between the  
contacts, suitable for the load indicated and  
complying with current directives, must be installed  
between the appliance and the mains (the earthing  
wire must not be interrupted by the circuit-breaker).  
The power supply cable must be positioned so that it  
does not exceed room temperature by 50°C at any  
point of its length. Before making the connection  
check that:  
• the circuit breakers or fuses of the home system  
can support appliance load (see data plate);  
• the power supply system has an efficient earthing  
connection which complies with the provisions of  
current regulations and the law;  
BROWN  
BLUE “NEUTRAL” (N)  
CROSS-BAR  
CORD GRIP  
BLUE  
BROWN  
“LIVE” (L)  
GREEN AND YELLOW  
“EARTH” (E)  
Disposing of the appliance  
When disposing of the appliance please remove the  
plug by cutting the mains cable as close as possible  
to the plug body and dispose of it as described  
above.  
! The plug and socket must be easily accessible.  
DATA PLATE  
width cm 43.5  
• there is easy access to the socket or the omnipolar  
circuit-breaker once the cooker has been installed.  
! do not use reducers, adapters or shunts as these  
could cause heating or burning.  
Dimensions  
Volume  
height cm 32  
depth cm 40  
lt. 56  
voltage: 230-240V ~ 50/60Hz  
maximum power absorbed  
2250W-2400W  
Electrical  
Connection n° 2  
connections  
Disposing of the plug.  
Directive 2002/40/EC on the label  
of electric ovens.  
! THIS APPLIANCE MUST BE EARTHED.  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be  
accidentally inserted into a socket. Instructions for  
connecting cable to an alternative plug:  
! the wires in the mains lead are coloured in  
accordance with the following code:  
Standard EN 50304  
ENERGY LABEL  
Declared energy consumption for  
Forced convection Class – heating  
mode: Fan assisted  
This appliance conforms to the  
following European Economic  
Community directives:  
- 2006/95/EEC of 12/12/06 (Low  
Voltage) and subsequent  
amendments;  
- 2004/108/EEC of 15/12/04  
(Electromagnetic Compatibility) and  
subsequent amendments;  
- 93/68/EEC of 22/07/93 and  
subsequent amendments.  
- 2002/96/EC and subsequent  
amendments.  
Green & Yellow  
Blue  
Brown  
-Earth  
-Neutral  
-Live  
If the colours of the wires in the mains lead do not  
correspond with the coloured markings identifying the  
terminals in your plug, proceed as follows.  
Connect Green & Yellow wire to terminal marked “E”  
or 6 or coloured Green or Green & Yellow.  
Connect Brown wire to terminal marked “L” or  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
3
 
Description of the appliance  
Overall view  
GB  
GUIDES for the  
sliding racks  
Control panel  
position 5  
position 4  
position 3  
position 2  
position 1  
GRILL  
DRIPPING PAN  
Control panel  
Indicator light  
THERMOSTAT  
TIMER  
Knob*  
SELECTOR  
VARIABLE GRILL  
Knob  
Knob  
Indicator light  
ELECTRONIC  
THERMOSTAT  
programmer*  
SELECTOR  
Knob  
VARIABLE GRILL  
Knob  
* Only on certain models  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
4
 
Start-up and use  
! The first time you use your appliance, heat the  
empty oven with its door closed at its maximum  
temperature for at least half an hour. Ensure that the  
room is well ventilated before switching the oven off  
and opening the oven door. The appliance may  
produce a slightly unpleasant odour caused by the  
burning away of protective substances used during  
the manufacturing process.  
Cooling ventilation  
GB  
In order to cool down the external temperature of the  
oven, some models are fitted with a cooling fan that  
blows out air between the control panel and the oven  
door.  
! Once the cooking has been completed, the cooling  
fan remains on until the oven has cooled down  
sufficiently.  
Starting the oven  
Oven light  
with the SELECTOR  
It goes on when selecting  
knob. It stays on when a cooking mode is selected.  
1. Select the desired cooking mode by turning the  
SELECTOR knob.  
2. Select the desired temperature with the VARIABLE  
GRILL knob. See the Cooking advice table for cooking  
modes and the suggested cooking temperatures (see  
Cooking Modes).  
3. When preheating is finished, the THERMOSTAT  
indicator light will stay on: place the food in the oven.  
4. You may do the following during cooking:  
- change the cooking mode by turning the SELECTOR  
knob.  
How to use the timer  
*
1. To set the buzzer, turn the TIMER knob clockwise  
almost one complete revolution.  
2. Turn the knob anticlockwise to set the desired  
time: align the minutes shown on the knob with the  
indicator on the control panel.  
3. The timer operates in minutes: when the selected  
time has elapsed, a buzzer will sound.  
- change the temperature by turning the VARIABLE  
GRILL knob.  
- stop cooking by turning the SELECTOR knob to the  
“0” position.  
! The timer does not turn the oven on or off.  
! Never put objects directly on the oven bottom to  
avoid damaging the enamel coating.  
! Always place cookware on the rack(s) provided.  
* Only on certain models  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
5
 
Cooking modes  
Cooking modes  
Practical cooking advice  
GB  
! GRILL (recommended: set only to MAX power level);  
! Do not place racks in position 1 and 5 during fan-  
assisted cooking. Excessive direct heat can burn  
temperature sensitive foods.  
Thermostatically controlled oven (Fan Assisted  
Mode)  
! In the GRILL cooking modes, place the dripping pan  
in position 1 to collect cooking residues (fat and/or  
grease).  
When the SELECTOR knob is turned in a clockwise  
direction to the symbol  
the fan and oven light  
will come on to assist in the defrosting of frozen  
food. Rotating further to the complete range of  
temperatures shown on the dial you can choose  
which is most suitable for the food you are going to  
cook. The temperature is reached automatically and  
controlled by the oven thermostat (from 60°C to  
MAX).  
GRILL  
• Insert the rack in position 3 or 4. Place the food in  
the centre of the rack.  
• We recommend that you set the maximum power  
level. The top heating element is regulated by a  
thermostat and may not always be on.  
! Whilst using tag oven for conventional VARIABLE  
GRILL knob must be set with “MAX” in line with the  
reference mark on the control panel.  
PIZZA  
• Use a light aluminium pizza pan. Place it on the  
rack provided.  
GRILL mode  
For a crispy crust, do not use the dripping pan  
(prevents crust from forming by extending cooking  
time).  
The top heating element comes on. The extremely  
high and direct temperature of the grill makes it  
possible to brown the surface of meats and roasts  
while locking in the juices to keep them tender. The  
grill is also highly recommended for dishes that  
require a high temperature on the surface: such as  
beef steaks, veal, rib steak, filets, hamburgers etc...  
Some grilling examples are included in the “Practical  
Cooking Advice” paragraph. Always cook in this mode  
with the oven door partially open.  
• If the pizza has a lot of toppings, we recommend  
adding the mozzarella cheese on top of the pizza  
halfway through the cooking process.  
To operate the grill:  
1. Turn the oven SELECTOR knob clockwise until the  
required grilling symbol is in line with the mark on  
the control panel. The element is now “on”.  
2. The VARIABLE GRILL knob can now be operated  
to select the required heat.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
6
 
Cooking advice table  
GB  
Foods  
Weight. Rack position  
(wt)  
Temperature  
(°C)  
Variable  
grill  
Pre-heating time Cooking  
(min)  
time  
(min.)  
Pasta  
Lasagne  
Cannelloni  
Oven-baked  
noodles  
Meat  
Veal  
Chicken  
Turkey  
Duck  
Rabbit  
Pork  
Lamb  
Fish  
2.5  
2.5  
2.5  
3
3
3
210  
210  
210  
-
-
-
75-80  
75-80  
75-80  
MAX  
MAX  
1.7  
1.5  
3.0  
1.8  
2
2.1  
1.8  
3
3
3
3
3
3
3
230  
220  
MAX  
230  
230  
230  
230  
-
-
-
-
-
-
-
85-90  
110-115  
95-100  
120/125  
105/110  
100/110  
90-95  
Mackerel  
Dentex  
Trout baked in  
paper  
Pizza  
1.1  
1.5  
1.0  
3
3
3
210-230  
210-230  
210-230  
-
-
-
55-60  
60-65  
40-45  
MAX  
Napolitan  
Cake  
Biscuits  
Tarts  
Chocolate cake  
Raised Cakes  
Grill cooking  
Toast  
Pork chops  
Mackerel  
1.0  
3
MAX  
MAX  
MAX  
15  
30-35  
0.5  
1.1  
1
3
3
3
3
180  
180  
200  
200  
15  
15  
15  
15  
30-35  
30-35  
45-50  
50/55  
1
n.° 4  
1.5  
1.1  
4
4
4
5
5
5
5-6  
20-30  
20-30  
3/4  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
7
 
The electronic cooking  
programmer  
Programming cooking  
GB  
! A cooking mode must be selected before  
DISPLAY  
programming can take place.  
END OF  
CLOCK icon  
TIMER icon  
Programming the cooking duration  
COOKING icon  
DURATION  
•• ••  
1. Press the  
button several times until the  
icon  
icon and the three digits on the DISPLAY begin to  
flash.  
2. Use the “+” and “-” buttons to set the desired  
duration; if you press and hold either button, the  
display will scroll through the values more quickly,  
making it quicker and easier to set the value.  
DECREASE TIME  
INCREASE TIME  
button  
button  
SET TIME  
button  
3. Wait for 10 seconds or press the  
to finalise the setting.  
4. When the set time has elapsed, the text END  
appears on the DISPLAY, the oven will stop cooking  
and a buzzer sounds.  
• For example: it is 9:00 a.m. and a time of 1 hour  
and 15 minutes is programmed. The programme  
will stop automatically at 10:15 a.m.  
button again  
Setting the clock  
! The clock may be set when the oven is switched  
off or when it is switched on, provided that a the end  
time of a cooking cycle has not been programmed  
previously.  
After the appliance has been connected to the  
mains, or after a blackout, the  
icon and the four  
numerical digits on the DISPLAY will begin to flash.  
Setting the end time for a cooking mode  
! A cooking duration must be set before the cooking  
end time can be scheduled.  
1. Press the button several times until the  
icon and the four digits on the display begin to  
flash.  
2. Use the “+” and “-” buttons to adjust the time; if  
you press and hold either button, the display will  
scroll through the values more quickly, making it  
quicker and easier to set the desired value.  
1. Follow steps 1 to 3 to set the duration as detailed  
above.  
2. Next, press the  
button until the  
icon and  
the four digits on the DISPLAY begin to flash.  
3. use the “+” and “-” buttons to adjust the cooking  
end time; if you press and hold either button, the  
display will scroll through the values more quickly,  
making it quicker and easier to set the desired  
value.  
3. Wait for 10 seconds or press the  
to finalise the setting.  
button again  
Setting the timer  
! This function does not interrupt cooking and does  
not affect the oven; it is simply used to activate the  
buzzer when the set amount of time has elapsed.  
4. Wait for 10 seconds or press the  
to finalise the setting.  
button again  
5. When the set time has elapsed, the text END  
appears on the DISPLAY, the oven will stop cooking  
and a buzzer sounds.  
1. Press the  
button several times until the  
icon and the three digits on the display begin to  
flash.  
2. Use the “+” and “-” buttons to set the desired  
time; if you press and hold either button, the display  
will scroll through the values more quickly, making it  
quicker and easier to set the value.  
Programming has been set when the  
and  
buttons are illuminated. The DISPLAY shows the  
cooking end time and the cooking duration  
alternately.  
Cancelling a programme  
3. Wait for 10 seconds or press the  
to finalise the setting.  
The display will then show the time as it counts  
down. When this period of time has elapsed the  
buzzer will be activated.  
button again  
To cancel a programme:  
• press the  
button until the icon corresponding to  
the setting you wish to cancel and the digits on the  
display are no longer flashing. Press the “-” button  
until the digits 00:00 appear on the display.  
• Press and hold the “+” and “-” buttons; this will  
cancel all the settings selected previously,  
including timer settings.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
8
 
Precautions and tips  
! The appliance was designed and manufactured in  
compliance with international safety standards. The  
following warnings are provided for safety reasons  
and must be read carefully.  
• In the case of a malfunction, under no  
circumstances should you attempt to repair the  
appliance yourself. Repairs carried out by  
inexperienced persons may cause injury or further  
malfunctioning of the appliance. Contact a Service  
Centre (see Assistance).  
GB  
General safety  
• Do not rest heavy objects on the open oven door.  
• The appliance should not be operated by people  
(including children) with reduced physical,  
sensory or mental capacities, by inexperienced  
individuals or by anyone who is not familiar with  
the product. These individuals should, at the very  
least, be supervised by someone who assumes  
responsibility for their safety or receive  
• The appliance was designed for domestic use  
inside the home and is not intended for  
commercial or industrial use.  
• The appliance must not be installed outdoors,  
even in covered areas. It is extremely dangerous  
to leave the appliance exposed to rain and  
storms.  
• When handling the appliance, always use the  
handles provided on the sides of the oven.  
• Do not touch the appliance with bare feet or with  
wet or moist hands and feet.  
preliminary instructions relating to the operation of  
the appliance.  
• Do not let children play with the appliance.  
The appliance must be used by adults only for  
the preparation of food, in accordance with the  
instructions outlined in this booklet. Any other  
use of the appliance (e.g. for heating the room)  
constitutes improper use and is dangerous.  
The manufacturer may not be held liable for  
any damage resulting from improper, incorrect  
and unreasonable use of the appliance.  
When the appliance is in use, the heating  
elements and some parts of the oven door  
become extremely hot. Make sure you don't  
touch them and keep children well away.  
• Ensure that the power supply cable of other  
electrical appliances does not come into contact  
with the hot parts of the oven.  
Disposal  
• Observe local environmental standards when  
disposing packaging material for recycling  
purposes. Observe existing legislation when  
disposing of the old appliance.  
• The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment (WEEE),  
requires that old household electrical appliances  
must not be disposed of in the normal unsorted  
municipal waste stream. Old appliances must be  
collected separately in order to optimise the  
recovery and recycling of the materials they  
contain and reduce the impact on human health  
and the environment. The crossed out “wheeled  
bin” symbol on the product reminds you of your  
obligation, that when you dispose of the  
• The openings used for ventilation and dispersion  
of heat must never be covered.  
• Always grip the oven door handle in the centre:  
the ends may be hot.  
• Always use oven gloves to place cookware in the  
oven or when removing it.  
appliance it must be separately collected.  
Consumers should contact their local authority or  
retailer for information concerning the correct  
disposal of their old appliance.  
• Do not use aluminium foil to line the bottom of the  
oven.  
• Do not place flammable materials in the oven: if  
the appliance is switched on by mistake, it could  
catch fire.  
• Always make sure the knobs are in the “”/“”  
position when the appliance is not in use.  
• When unplugging the appliance always pull the  
plug from the mains socket, do not pull on the  
cable.  
• Never carry out any cleaning or maintenance work  
without having unplugged the plug from the  
mains.  
Respecting and conserving the  
environment  
• By using the appliance in the hours between late  
afternoon and early morning, you can help reduce  
the work load placed on electrical companies.  
• Regularly check the door seals and wipe clean to  
ensure they are free of debris so that they stick  
properly to the door and do not allow heat to  
disperse.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
9
 
Maintenance and care  
Switching the appliance off  
3. Grip the door on the two  
external sides and close it  
approximately half way. Then  
pull the door towards you  
lifting it out of its seat (see  
diagram).  
GB  
Disconnect your appliance from the electricity  
supply before carrying out any work on it.  
Cleaning the appliance  
To replace the door, reverse  
this sequence.  
• The stainless-steel or enamel-coated external  
parts as well as the rubber seals may be cleaned  
using a sponge that has been soaked in  
lukewarm water and neutral soap. If these stains  
are difficult to remove, use only specialised  
products. After cleaning, rinse and dry  
thoroughly. Do not use abrasive powders or  
corrosive substances.  
Inspecting the seals  
Check the door seals around the oven periodically. If  
the seals are damaged, please contact your nearest  
After-sales Service Centre (see Assistance). We  
recommend not using the oven until the seals have  
been replaced.  
• Ideally, the inside of the oven should be cleaned  
after each use, when it is still lukewarm. Use hot  
water and detergent, rinse and dry with a soft  
cloth. Do not use abrasive products.  
Replacing the light bulb  
• The accessories can be washed like everyday  
crockery (even in your dishwasher).  
To replace the oven light bulb:  
! Never use steam cleaners or pressure cleaners on  
the appliance.  
Cleaning the oven door  
Clean the glass part of the oven door using a  
sponge and a non-abrasive cleaning product, then  
dry thoroughly with a soft cloth. Do not use rough  
abrasive material or sharp metal scrapers as these  
could scratch the surface and cause the glass to  
crack.  
To clean more thoroughly, you can remove the oven  
door.  
1. Remove the glass cover of the lamp-holder.  
2. Remove the light bulb and replace it with a similar  
one: Wattage 25 W, cap E 14.  
1. Open the oven door fully  
(see diagram)  
3. Replace the glass cover (see diagram).  
Assistance  
Communicating:  
• appliance model (Mod.)  
• serial number (S/N)  
2. Lift up and turn the small  
levers located on the two  
hinges (see diagram)  
This information is found on the data plate located on  
the appliance and/or on the packaging.  
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24  
10  
 
Guarantee  
12 months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for  
twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either  
workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our operating and  
maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any  
person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper  
installation.  
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables, batteries,  
light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOTAPPLY IF THEAPPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Indesit also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you registering  
your appliance with us and the parts being fitted by one of our authorised engineers. There will be a charge for  
our engineer’s time. To activate the extra parts warranty on your appliance, simply call our registration line on  
08448 24 24 24 (Republic of Ireland 01 230 0800)  
Extended Guarantees  
We offer a selection of protection plans that enable you to fully cover yourself against the expense of repair bills  
for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226 (Republic of  
Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you experience  
any technical difficulties within the first 90 days of ownership. Simply call our Indesit Service Hotline on 08448  
224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to arrange for an  
engineer to call.  
 
11/2011 - 195088315.01  
XEROX FABRIANO  
After Sales Service  
No one is better placed to care for your Indesit appliance during the course of its working life than us – the  
manufacturer.  
Essential Contact Information  
Indesit Service  
We are the largest service team in the UK and Ireland offering you access to 400 skilled telephone advisors and  
1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically  
clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Indesit ownership. To activate your free 5 year parts guarantee you  
must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate, Dublin 17  
Recycling and Disposal Information  
As part of Indesit’s continued commitment to helping the environment, Indesit reserves the right to use quality,  
recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the  
door, plug, and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure that  
the appliance can no longer be plugged into mains socket, and the door cannot be locked shut.  
 

Init TV Mount 8832 000198 User Manual
Interphase Tech GPS Receiver Pilot GPS User Manual
Janome Sewing Machine MS 5027 User Manual
John Lewis Clothes Dryer JLTDC 05 User Manual
JVC CD Player KD G637 User Manual
JVC Stereo System CA FSJ50 User Manual
Kambrook Popcorn Poppers KPC10 User Manual
KitchenAid Ventilation Hood 423 User Manual
Kodak Camera Lens KAF 4320 User Manual
Kodak Digital Camera CX7330 User Manual