MD-RECEIVER
KMD-671R
INSTRUCTION MANUAL
B64-1609-00 (EN)
Safety precautions
IMPORTANT INFORMATION
2WARNING
2CAUTION
You cannot connect the unit directly to the
following CD automatic changers. For users
who want to use older changers with the
unit, follow the directions below according to
the type of changer you own:
To prevent injury and/or fire, take the
following precautions:
• Insert the unit all the way until it is fully
locked in place. Otherwise it may fly out of
place during collisions and other jolts.
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• KDC-C200 / KDC-C300 / KDC-C400
• Do not open the top or bottom covers of the
unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
• Do not set the removed faceplate or the
faceplate case in areas exposed to direct
sunlight, excessive heat or humidity. Also
avoid places with too much dust or the
possibility of water splashing.
• To prevent deterioration, do not touch the
terminals of the unit or faceplate with your
fingers.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision
equipment.
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
• To prevent short circuits when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
Use the extension cable and the control box
attached to the CD changer, and the optional
CA-DS100 converter cable.
• KDC-C301 / KDC-C600 / KDC-C800 / KDC-
C601 / KDC-C401
Use the extension cable attached to the CD
changer, and the optional CA-DS100
converter cable.
• KDC-C100 / KDC-C302 / C205 / C705 /
non-Kenwood CD changers
• When extending the ignition, battery or
ground cables, make sure to use automotive-
grade cables or other cables with an area of
2
0.75mm (AWG18) or more to prevent cable
deterioration and damage to the cable
coating.
• To prevent short circuits, never put or leave
any metallic objects (e.g., coins or metal
tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
• Make sure not to get your fingers caught
between the faceplate and the unit.
• Be careful not to drop the unit or subject it to
strong shock.
The unit may break or crack because it
contains glass parts.
• Do not touch the liquid crystal fluid if the
LCD is damaged or broken due to shock. The
liquid crystal fluid may be dangerous to your
health or even fatal.
If the liquid crystal fluid from the LCD
contacts your body or clothing, wash it off
with soap immediately.
Cannot be used with this model.
2CAUTION
You can damage both your unit and
the CD changer if you connect them
incorrectly.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1. It means
that the unit is utilizing laser beams that are
of a weaker class. There is no danger of
hazardous radiation outside the unit.
• During installation, do not use any screws
except for the ones provided. The use of
improper screws might result in damage to
the main unit.
— 3 —
Safety precautions
Handling Mini discs
Lens Fogging
NOTE
• The MD shutter is designed so that it cannot
be opened. If forced open, the cartridge will
be damaged and use of the MD will no
longer be possible. If the shutter has been
opened due to some cause, be careful not to
touch the recording portion with a finger.
Doing so will cause the sound to skip.
In cold climates, there may be a period after
you turn on your vehicle's heater when the
lens that guides the laser beam used in your
MD player fogs up. If this happens, you
cannot play mini discs. Take out discs and
the fogging will disappear. If it does not
return to normal after several hours, contact
your Kenwood dealer.
• If you experience problems during
installation, consult your Kenwood dealer.
• If the unit does not seem to be working
right, try pressing the reset button first. If
that does not solve the problem, consult
your Kenwood dealer.
Egnlish
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
Reset button
• Characters in the LCD may become difficult
to read in temperatures below 41 ˚F (5 ˚C).
• Do not use an MD that has a peeling label.
Use of an MD that has a loose or peeling
label may cause problems, such as the label
coming off inside the player and the
Cleaning the Unit
If the front panel gets dirty, turn off the
power and wipe the panel with a dry silicon
cloth or soft cloth.
• The illustrations of the display and the panel
appearing in this manual are examples used
to explain more clearly how the controls are
used. Therefore, what appears on the display
in the illustrations may differ from what
appears on the display on the actual
equipment, and some of the illustrations on
the display may represent something
impossible in actual operation.
• The functions that can be used and the
information that can be displayed will differ
depending on the external disc players being
connected.
resultant inability to eject the MD.
2CAUTION
• Wipe away dirt or dust from the cartridge
surface with a dry cloth before use. Using an
oil-soiled cartridge in particular may result in
the disc not loading or being unable to eject
it. (At time of cleaning, be careful not to
open the shutter.)
• Do not leave the MD in the unit for a
prolonged period. The ejected MD should be
placed in an MD case for storage.
• Do not leave the MD in a place exposed to
direct sunlight (such as on a instrument
panel) or in other places that reach high
temperatures. The MD cartridge will become
misshapen and will no longer be usable.
Do not wipe the panel with a stiff cloth or a
cloth dampened by volatile solvents such as
paint thinner and alcohol. They can scratch
the surface of the panel and/or cause the
indicator letters to peel off.
• MDs designed for use with data cannot be
used. Please use MDs designed for music.
• Do not use lens cleaners. Doing so will lead
to breakdown.
US and foreign patents Iicensed from Dolby
Laboratories Licensing Corporation.
— 4 —
General features
Power
Turning on the power:
Press the SRC button.
NOTE
Turn the power on before carrying out the following procedures.
Turning off the power:
Hold down the PWR OFF button for one second or more.
Volume
Increasing Volume:
Press the u button to turn up the volume.
Decreasing Volume:
Press the d button to turn down the volume.
ATT indicator
Attenuator
This function allows you to turn down the volume quickly.
Turning Attenuator On/Off:
Press the ATT button to switch the attenuator on and off.
When the attenuator is on, the ATT indicator blinks.
When the attenuator is off, the volume returns to the original
level.
LOUD indicator
NOTE
Turning the volume up, or turning it all the way down deactivates
the attenuator function.
— 5 —
General features
Switching Modes
Loudness
This function amplifies low and high tones when the volume is
Switching Modes:
turned down.
Each time you press the SRC button, the mode switches as
follows:
The LOUD indicator lights up, when the loudness function is
on.
Egnlish
▼
Turning Loudness On/Off:
Tuner mode
Hold down the LOUD button for one second or more to switch
the loudness on and off.
▼
MD mode
▼
External disc control mode 1
▼
External disc control mode 2/AUX mode
▼
Audio Control Setting
Adjust various parameters of sound quality.
Standby mode
1
2
Press the AUD button to enter the control mode.
Selecting the standby mode:
Press the SRC button repeatedly to select to "ALL OFF" .
When "ALL OFF" is displayed, the standby mode is turned on.
The standby mode turns all functions off although leaving the
unit’s power on. Use this mode when you want to have the
display illuminated but do not want to listen to anything.
Selecting mode
Press either the FM or AM button.
Each time the button is pressed, the adjustment mode will
change.
Please refer to the following for the contents of the
adjustment modes.
NOTE
• The mode switches to the next mode from any mode which
cannot be used.
NOTE
Source tone memory
Each source (CD, MD, FM, AM, and disc changer) has its own
memory in which to store the bass and treble tone settings.
The settings made for a particular source are then recalled
automatically whenever you use that source (e.g., FM mode uses
the tone settings made for FM, AM for AM, etc.).
• The external disc control mode will differ depending on the unit
that is connected.
• The AUX mode is available only when the changer / AUX
switching adapter (KCA-S210A or CA-C1AX) or CD changer
(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is
connected to this unit.
During the AUX mode, "AUX" / AUX-name will show in the
display. When the CA-C1AX is being used, the AUX Mode will
replace the External Disc Control Mode.
3
Adjust each mode
Press the 4/¢ button.
Please refer to the following for the adjusting values.
4
Press the AUD button to end the control mode.
NOTE
Presetting AUX-name
In the AUX mode, press the NAME.S button for two seconds or more.
"NAME SET" is display and AUX-name mode is entered.
Input the characters, referring to the section on "Presetting Disc
Names (DNPS)" (page 20).
— 6 —
• You can call the following settings with this function; bass
centre frequency, bass level, bass quality factor, bass
extension, treble centre frequency, and treble level setting.
Their setting values are different depending on the setting of
the mobile preset plan mode.
"Bass" : Adjust the bass level.
Setting values: - 8 – + 8
"Treble" : Adjust the treble level.
Setting values: - 8 – + 8
Mobile Preset
This function allows you to adjust the setting that is recalled
with the sound coordinate system, according to types of
speakers.
"Balance" : Adjust the balance level.
Setting values: Left 15 – Right 15
1
Press the SRC button repeatedly to select the standby mode.
"ALL OFF" is displayed when the standby mode is selected.
2
3
Press the AUD button to enter the mobile preset plan mode.
Press either the 4 or ¢ button to select the type of
speaker. The setting switches as follows.
Off / For the OEM speaker / For 6/6x9 in. speaker /
For 5/4 in. speaker
"Fader" : Adjust the fader level.
Setting values: Rear 15 – Front 15
4
Press the AUD button to end the mobile preset plan mode.
NOTE
"V OFFSET" : Set the sound level of the each source selected by
adjusting the level difference between the basic
sound level and the required level.
• This mode is available only when the Sound coordinate system
is on. (page 24)
• When you change the setting of type of speaker, the bass and
treble tone settings are returned to original levels.
Setting values: - 8 –
0
"ec4"/"dB" : Recalling the kenwood preset sound setting
Press the preset buttons (#1-6).
Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy,
#6;Scan of #1-5
NOTE
• This mode is available only when the Sound coordinate system
is on. (page 24)
— 7 —
General features
NOTE
TEL Mute
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate
in its special storage case whilst detached.
Shut down the audio system temporarily whenever an
incoming call is received.
Egnlish
NOTE
The function will not work if a cable is not connected to the car
phone.
When the telephone rings:
When a call is received, "CALL" is displayed and all the unit
functions are temporarily interrupted.
• Do not expose the faceplate or its storage case to direct
sunlight or excessive heat or humidity. Also avoid places with
too much dust or the possibility of water splashing.
Restoring Original Unit Source During Phone Call:
Press the SRC button.
Reattaching Faceplate:
"CALL" disappears from the display, and the volume of the
original source is restored gradually.
1
Align the projections on the unit with the grooves on the
faceplate.
Turning TEL Mute Function Off After Phone Call:
Hang the phone up.
2
Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use the unit.
"CALL" disappears from the display.
The original source (i.e., the one used before the phone call) is
returned to automatically, and the volume restored gradually.
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken with you,
helping to deter theft.
Projections
Release button
Grooves
Removing Faceplate:
Press the release button.
The faceplate is unlocked, allowing you to detach it.
— 8 —
Tuner features
Tuning
1
Press the SRC button repeatedly until the tuner mode is
obtained. "TUNER" is displayed only when the tuner mode is
selected.
2
Press either the FM or AM button to select the band.
Each time you press the FM button, the band switches
between the FM1, FM2 and FM3.
Press the AM button to select the MW and LW bands.
3
• Auto Seek Tuning
Press the ¢ button to seek increasing frequencies.
Press the 4 button to seek decreasing frequencies.
• Preset station seek tuning
Press the ¢ button to move to the next preset station (i.e.,
the one with the next highest number), and the 4 button to
move to the last preset station (i.e., the one with the next
lowest number).
NOTE
If the frequencies stored at the preset numbers receive
stations which were not originally memorized when traveling
long distances, the preset number is not displayed. In such
cases, pressing the 4/¢ button to use preset station
seek will receive channel 1.
Band display
Preset station number
Frequency
ST indicator
• Manual Tuning
Press the ¢ button to increase the frequency by one step.
Press the 4 button to decrease the frequency by one step.
NOTE
• The ST indicator lights up when stereo broadcasts are being
£ indicator
AUTO indicator
received.
• Please see the menu settings about selecting tuning mode.
(page 25)
— 9 —
Tuner features
NOTE
Station Preset Memory
• If the RDS station currently tuned to is transmitting no text
whilst the Radio Text Display mode is turned on, "NO TEXT" will
appear in the display. Whilst awaiting reception, "WAITING" will
be displayed.
Store the frequency of the station currently being listened to.
You can then recall that station with a single touch of a button.
Egnlish
1
2
Select the band/ station that you want to have stored.
• The £ indicator lights whilst the clock is displayed.
Hold down the button (#1-6) that you want to use for the
station, for two seconds or more.
2WARNING
The button number blinks once in the display to indicate that
the data has been stored.
To prevent accidents, drivers should not look at the display whilst
on the road.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
NOTE
You can store 6 stations in each of the FM1, FM2, FM3, and AM
(MW and LW) bands.
Switching Display for Tuner
You can change the display used when listening to the radio.
Switching the Display:
Pressing the CLK button switches the display as follows.
Select the Radio Text Display mode.
Programme Service name (during RDS station reception)/Station frequency
Radio text
Clock
Date
Displaying Frequencies:
Hold down the CLK button for one second or more.
The frequency for the RDS station will be displayed for five
seconds instead of the station name.
— 10 —
RDS features
RDS (Radio Data System)
RDS is a digital information system that lets you receive
signals besides those of regular radio programmes, such as
network information being transmitted from radio stations.
When listening to an RDS station (ie, a station with RDS
capability), the programme service name of the station is
displayed along with the frequency, advising you quickly which
station is being received.
RDS (Radio Data System) stations also transmit frequency data
for the same station. When you are making long trips, this
function automatically switches to the particular frequency
with the best reception for the particular network of stations
that you want to listen to. The data is automatically stored,
allowing you to switch quickly to another RDS stations,
broadcasting the same programme, that has better reception.
These include stations stored in the station preset memory that
you often listen to.
Enhanced Other Network
Stations that offer <Enhanced Other Network> also transmit
information about other RDS stations that have traffic
information. When you are tuned to a station that is not
transmitting traffic information, but another RDS station starts
transmitting a traffic bulletin, the tuner automatically switches
to the other station for the duration of the bulletin.
Band display
£ indicator
Alarm
™ indicator
NEWS indicator
TI indicator
PTY indicator
When an emergency transmission (announcing disasters, etc.)
is sent, all current functions are interrupted to allow the
warning to be received.
— 11 —
RDS features
17. Finance
(Finance)
Programme Type (PTY) Function
Conduct auto seek tuning only on those stations with selected
kinds of programmes.
18. Children’s programmes (Children)
19. Social Affairs
20. Religion
(Social A)
(Religion)
(Phone In)
(Travel)
(Leisure)
(Jazz)
(Country)
(Nation M)
(Oldies)
(Folk M)
(Document)
Egnlish
21. Phone In
1
Hold down the PTY button for one second or more.
"PTY" is displayed, and the Programme Type Selection (PTY)
Mode entered.
If you make no key input in 30 seconds, the mode will
automatically turn off.
22. Travel
23. Leisure
24. Jazz Music
25. Country Music
26. National Music
27. Oldies Music
28. Folk Music
29. Documentary
NOTE
You cannot use this function whilst the traffic bulletin is received.
NOTE
Changing the Display Language to French, German, or Swedish
(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)
• You can select the type of programme directly by pressing a
preset button. The buttons are factory-set to the following
type of programmes:
In the PTY mode, press the CLK button to display the name of
the language currently used.
If you want to change the language, press the preset button for
the desired language and then the CLK button.
1. Music
4. Other Music
2. Speech
5. Serious Classical
3. News
6. Varied
English is #1, French is #2, German is #3, and Swedish is #4
2
Select the type of programme to be received
• Press either the FM or AM buttons repeatedly until the type
of programme you want to listen to.
NOTE
Changing the Preset Button Settings for Programme Type
After selecting the type of programme to be stored in a certain
preset button, hold down that button for two seconds or more.
The previously stored data for that button are erased and the
new programme type is stored.
The selection includes:
Speech
(Speech)
(Music)
Music
3
Seeking the selected programme type
1. News
(News)
Press the 4 or ¢ button to make a seek of frequencies
2. Current Affairs
3. Information
4. Sports
(Affairs)
(Info)
(Sport)
(Educate)
(Drama)
(Culture)
(Science)
(Varied)
with your selected type of programme.
The display blinks and the seek starts.
"PTY" blinks in the display for about 30 seconds.
If you make no key input in 30 seconds, the PTY selection
mode will turn off automatically.
5. Education
6. Drama
7. Culture
8. Science
NOTE
9. Varied
If no programme can be found, "NO PTY" is displayed.
If you want to select another type of programme, repeat steps 2
and 3 above.
10. Pop Music
11. Rock Music
12. Easy Listening Music
13. Light Classical
14. Serious Classical
15. Other Music
16. Weather
(Pop M)
(Rock M)
(Easy M)
(Light M)
(Classics)
(Other M)
(Weather)
Switching to Other Stations with the Same Type of Programme:
When "PTY" is blinking in the display, perform auto seek tuning.
The tuner scans for another station with the same type of
programme.
— 12 —
Cancelling Programme Type Function During Its Operation:
• Holding the TI button down for one second or more when the
TI function is on in the disc control mode results in a change to
the frequency display of the traffic information station for five
seconds.
Press the PTY button for one second or more.
Traffic Information Function
You can listen to traffic information. If you are listening to
tapes or discs, they will continue playing until a traffic bulletin
is broadcast.
Presetting Volume for Traffic Information/News
Preset the volume level to be used for traffic information and
news broadcasts.
1
2
3
Tune into the station for which you want to set the volume.
Adjust the volume to the desired level.
Turning TI function On/Off:
Press the TI button to turn the function on and off.
When the function is on, the TI indicator is turned on.
When none is being received, the TI indicator will blink on and
off. When a traffic information station is being received, the TI
indicator will turn on.
Hold down the VOL ADJ button for two seconds or more.
The volume level blinks once in the display to indicate that the
data has been stored.
Future traffic information/news broadcasts are heard at the
preset level.
When a traffic bulletin begins to be broadcast, "TRAFFIC" will
be displayed, and reception will begin at the preset volume.
If you are listening to a tape or disc when a traffic bulletin
begins, they will automatically be turned off. When the bulletin
ends or poor reception is experienced, the tape or disc will
begin playing again.
NOTE
• The volume cannot be lowered by this function during tuner
reception. The volume is only set when it is louder than the
listening volume of the tuner.
• You can arrange only to listen to traffic information or news
bulletins with at preset volume with the volume set at
minimum.
NOTE
Pressing the TI button whilst in the MW/LW band automatically
switches reception to the FM band. However, the MW/LW band
is not returned to when the TI button is pressed again.
Switching to a Different Traffic Information Station:
Use the 4 / ¢ buttons to make an auto seek of the TI
stations in a certain band.
NOTE
• When you are listening to a tape or disc, you cannot change to
another TI station.
• When the auto TP seek function is turned on and reception
starts to weaken, the tuner automatically seeks traffic
information stations with better reception.
• If you are tuned to a station that is not a traffic information
station itself but which provides <Enhanced Other Network>
services, you can still have traffic information received.
— 13 —
RDS features
MD/External disc control features
Radio Text Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
Egnlish
To scroll manually:
1
2
Press the CLK button to display the Radio Text.
Holding down the CLK button for one second or more results
in one scrolling display of the text.
To scroll automatically:
1
Press the CLK button to display the Radio Text.
The text will be displayed in one scrolling display.
2
Holding down the CLK button for one second or more results
in one scrolling display of the text.
NOTE
Please see the menu settings (page 26) about switching between
manual scrolling and automatic scrolling.
Disc number
(For disc changers)
Track time
Track number
3 indicator
MD-IN indicator
£ indicator
— 14 —
■ When a unit equipped with an O-N switch is to be
connected, please also see the instruction manual of this
unit.
2CAUTION
Do not attempt to insert an MD into the slot if another one is
already there.
Set the O-N switch to "N". "N"-operation will be set.
"N"-operation:
• The disc title and track title of the CD text can be displayed.
• The disc name will be displayed when the name has been
registered to any connected unit with the Presetting Disc
Names function, or when the playing unit contains a disc to
which the disc title has been recorded.
Playing Other Disc mode
This function permits the connection of optional players and
the playing of discs other than the loaded MD (in the current
unit).
"O"-operation:
• CD text cannot be displayed.
Playing Discs:
• Regardless of the control unit, the characters that can be
registered with the Presetting Disc Names function are "A~Z
0~9 /, +, –, ∗, =, <, >, [ , ]".
Press the SRC button repeatedly to select the external disc
control mode.
The disc will start playing.
NOTE
• The disc name will be displayed when the name has been
registered to the playing unit with the Presetting Disc Names
function.
The external disc control mode will differ, depending on the unit
that is connected.
Mode Display Examples
• "CD" ...when a CD player is connected
• "DISC" ...when a disc changer is connected
• "DISC-1" , "DISC-2" ...when two disc changers are connected
NOTE
The CD text, Presetting Disc Names, and Disc Name Preset Play
functions may not be operational depending on the unit.
NOTE
When one disc has finished playing its last track, the next disc in
the changer will start playing. When the last disc in the changer
has finished, the player will return to the first disc and start
playing it.
Playing MDs
Playing MDs:
If no MDs are inserted, insert one in the slot with the label
facing up.
If an MD is already inserted, press the SRC button repeatedly
until the MD mode.
"MD" is displayed when the MD mode has been selected.
The MD will start playing.
The MD-IN indicator lights up when an MD has been inserted.
The 3 indicator lights up when an MD is being played.
Stopping and Ejecting MDs:
Press the 0 button.
The MD stops playing and ejects from the slot.
— 15 —
MD/External disc control features
Reversing Disc Play:
Switching Display for Discs
Switch the display that appears whilst discs are playing.
Hold down on the 4 button.
Release your finger to play the disc at the point.
NOTE
Switching Display for Discs:
Egnlish
Each time you press the CLK button, the display during disc
play switches as follows.
You cannot use reverse play between tracks depending on the
model being connected. Instead, the reverse play function is
cancelled when it reaches the beginning of a track, at which
point normal play automatically resumes.
Track time
Disc name (DNPS)
Disc title (Units featuring CD text/MD only)
Track Search
Search forwards or backwards through the tracks on the disc
until you reach the one that you want to listen to.
Track title (Units featuring CD text/MD only)
Clock
Date
Making a Reverse Track Search:
Press the 4 button to display the desired track number.
Press once to search back to the beginning of the current
track, twice to search back to the beginning of the previous
track, and so forth.
NOTE
• DNPS:Function of disc changers
• You can give names to discs through the presetting disc name
function (see p.20).
Note that depending on the unit, display may not be possible.
• If you try to display the name of a disc that does not have one,
"NO NAME" is displayed instead.
• When there is an attempt to display the title of a disc for which
the disc title/track title has not been recorded, "NO TEXT" is
displayed for CD and "NO TITLE/NO NAME" is displayed for
MD.
• Depending on the type of characters of the CD Text, some
characters may not be displayable.
• The £ indicator lights whilst the clock is displayed.
Play starts at the beginning of the displayed track number.
NOTE
(For disc changers)
Pressing the 4 button whilst listening to track 1 only searches
back to the beginning of that track. The reverse search is not
"recycled" to the last track on the disc.
Making a Forward Track Search:
Press the ¢ button to display the desired track number.
Press once to fast forward to the next track, twice to fast
forward to the track after that, and so forth.
Play starts at the beginning of the displayed track number.
NOTE
(For disc changers)
You cannot make a forward track search when listening to the
last track on a disc.
Fast Forwarding and Reversing Disc Play
Fast Forwarding Disc Play:
Hold down on the ¢ button.
Release your finger to play the disc at that point.
— 16 —
Disc Search
Search forwards or backwards through the discs in a disc
changer until you reach the one that you want to listen to.
(Function of disc changers)
Track Scan
Successively play the beginning of each track on a disc until
you find the track that you want to listen to.
Making a Reverse Disc Search:
Starting the Track Scan:
Press the DISC– button to display the desired disc number.
Each time the button is pressed, the displayed disc number
decreases by one.
Press the SCAN button. "Scan/T-Scan ON" is displayed and the
first 10 seconds of each track are played, and the tracks are
played in order.
Play starts at the beginning of the displayed disc.
The track number currently being heard blinks in the display.
Making a Forward Disc Search:
Stopping to Listen to the Track Being Scanned:
Press the SCAN button again to stop the scan and keep on
listening to a track normally.
Press the DISC+ button to display the desired disc number.
Each time the button is pressed, the displayed disc number
increases by one.
NOTE
Play starts at the beginning of the displayed disc.
NOTE
• The track scan function is cancelled when you eject the disc.
• The track scan function only scans each track on a disc once.
"LOAD" is displayed when discs are being exchanged on the disc
changer.
Track / Disc Repeat
Repeat playing the current track or disc.
Turning Repeat Play Function On/Off:
Press the REP button to switch the repeat play function on and
off as follows :
▼
Track Repeat ON
▼
Disc Repeat ON (Function of disc changers)
▼
Track/Disc Repeat OFF
"Repeat/T-Repeat ON" is displayed and the track number blinks
in the display when track repeat is on.
"D-Repeat ON" is displayed and the disc number blinks in the
display when disc repeat is on.
NOTE
Repeat play is cancelled when you eject the disc.
— 17 —
MD/External disc control features
NOTE
Disc Scan
(Function of disc changers)
Random play is cancelled when you eject the disc.
Successively play the beginning of each disc on a changer
until you find the one that you want to listen to.
Egnlish
Starting the disc scan:
Press the D.SCN button. "D-Scan ON" is displayed and the first
10 seconds of each disc are played, in the order in which they
are loaded on the changer.
Magazine Random Play
Play the tracks on all the discs in the disc changer in random
order.
(Function of disc changers)
The disc number currently being heard blinks in the display.
Stopping to Listen to the Disc Being Scanned:
Press the D.SCN button again to stop the scan and keep on
listening to the disc normally.
1
Press the M.RDM button to switch the magazine random play
function on and off.
NOTE
"M-Random ON" is displayed when magazine random play is
turned on.
• The disc scan function is cancelled when you eject the disc.
• The disc scan function only scans each disc on the changer
once.
• "LOAD" is displayed when discs are being exchanged on the
disc changer.
The display of the disc and track numbers change continuously
as the next track is being selected.
When the disc/track has been selected, play starts.
The selected disc/track number blinks in the display as it is
being played.
NOTE
This function is not available with the following models:
KDC-C200/C300/C400/C301/C401
Random Play
Play all the tracks on the current disc in random order.
2
To change the track being heard, press the ¢ button.
Another disc/track is selected and played.
1
Press the RDM button to switch the random play function on
and off.
NOTE
• Magazine random play is cancelled when you eject the disc.
• The time needed for random selection depends on the number
of discs loaded in the disc magazine.
"Random ON" is displayed when random play is turned on.
The display of the track number changes continuously as the
next track is being selected.
When the track has been selected, play starts.
The selected track number blinks in the display as it is being
played.
NOTE
(For disc changers)
Text / Title Scroll
This function permits the text to be scrolled and the entire text
to be displayed. The scrolling method differs depending on the
setting of scrolling in the menu.
When all the tracks on a certain disc have been played using the
random play function, the next disc on the changer starts playing
(with the random play function still turned on).
2
To change the track being heard, press the ¢ button.
To scroll manually:
Another track is selected and played.
— 18 —
1
2
Press the CLK button to display the disc title or the track title.
Holding down the CLK button for one second or more results
in one scrolling display of the titles.
To scroll automatically:
1
Press the CLK button to display the disc title or the track title.
The titles will be displayed in one scrolling display.
NOTE
When the disc or track to be played changes, the title is
displayed in one scrolling display.
2
Holding down the CLK button for one second or more results
in one scrolling display of the titles.
NOTE
Please see the menu settings (page 26) about switching between
manual scrolling and automatic scrolling.
— 19 —
MD/External disc control features
Operations can be followed again from Step 2 at a time such
as this, and the characters to be input are selected using the
procedure described below.
Presetting Disc Names(DNPS) (Function of disc changers)
Store the names of discs to be displayed when played.
Press the DISC+ or DISC– button to display the desired
character. Besides the alphabet (capital letters only) and
numbers, you can choose the following characters: /, +, –, *,
=, <, >, [ and ].
1
Play the disc whose name you want to preset.
Egnlish
NOTE
• This function is not available for disc changers that do not
feature the Disc Name Preset function.
5
Continue steps 3 and 4 until all the characters are chosen for
the name.
NOTE
• This procedure is not to be used to store the disc and track
titles for MDs that you record.
• The disc name preset function cannot be used when a disc title
name or track title is displayed.
You can enter up to eight characters for each name.
6
2
Press the NAME.S button.
Hold down the NAME.S button for two seconds or more.
The disc name is stored and the disc name preset mode is
cancelled.
"NAME SET" is displayed and the disc name preset mode is
entered.
If you make no entry in a 10-second period, the name will be
stored with the characters input so far.
The cursor blinks in the position where character input can be
made.
NOTE
3
4
Press either the 4 or ¢ button to move the cursor to the
desired position.
• The number of characters and discs whose names can be
stored will differ depending on the disc changer that is
connected. Please see your disc changer manual for details.
• Discs are identified by their total length and number of tracks.
If another disc happens to have the same specifications as one
that you have already stored a name for, the name will be
displayed for it, too.
• If you want to change the name of a disc, repeat steps 1 and 2
to display the name, and then repeat steps 3 and 4 to input the
changes.
• Pressing the reset button does not erase the disc names stored
in a disc changer.
The 4 button moves the cursor to the left, and the ¢
button to the right.
Each time the TI button is pressed, the characters to be
entered change as listed below.
Press the DISC+ or DISC– button to display the desired
character.
Characters that can be displayed are as follows.
Alphabet (upper case): A ~ Z
Alphabet (lower case): a ~ z
Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]
Special characters: á
à
é
è
í
ì
ó
ò
ú
ù
Ñ
ë
î
ï
ô
ö
û
ü
ñ
ç
©
Æ
›
NOTE
The operation and characters that can be entered may change
as listed below, depending on the unit that is connected.
A press of the TI button exits the disc name preset mode.
— 20 —
Menu settings
Menu System
You can set the defaults for additional functions in the menu
mode.
Make a setting for each function, referring to the following
operations.
SRC
KMD-671R
1
2
PWR
OFF
PTY
+
Enter the menu mode
DISC
FM
Hold down the MENU button for one second or more.
"MENU" is displayed when the menu mode is entered.
The function that you can adjust is indicated with the current
settings displayed.
MENU
AUD
LOUD
SCAN
RDM
REP
D.SCN
M.RDM
AM
TI VOL ADJ
CLK NAME.S
-
ATT
DISC
1
2
3
4
5
6
Selecting function to set
Press the FM button to search through the functions until you
see the one you want to adjust in the display.
Press the AM button to search through the functions backward.
Example: If you want to switch the tuning mode from auto1 to
manual, first search through the functions until you
see "Auto 1" in the display.
3
4
Changing setting for currently displayed function
Press either the 4 or ¢ button.
Graphic display
Menu display
The setting will change for each function.
Example: The tuning mode will switch from auto 1 to auto 2.
Pressing the button again switches the setting to
manual, and "Manual" is displayed.
AUTO indicator
™ indicator
NEWS indicator
Ending the menu mode
Press the MENU button.
NOTE
Make sure to end the menu mode when finished.
If you fail to end the menu mode, several functions may not
operate properly, including the Traffic Information function, the
News Bulletin function with PTY news timeout setting, and the
Alarm function.
— 21 —
Menu settings
Display and setting:
Touch Sensor Tone
This function produces a beep sound that accompanies button
operation. It can be switched on or off.
1
Select the display "Date Adjust" during the selecting function in
the menu system.
2
Hold down either the 4 or ¢ button for two seconds or
more to enter the Calendar adjustment mode.
The date display will blink.
Egnlish
Display and setting:
"Beep ON" : Beep setting is on.
"Beep OFF" : Beep setting is off.
3
4
5
Selecting the item (day, month, or year) to adjust
Press the 4 or ¢ button.
NOTE
The beep sound is not output from the preout jacks.
The item blinking in the display can be adjusted.
Adjusting the date
Press the FM or AM button.
The item of the date blinking in the display will change.
Manual Time Adjustment
Adjust the time manually.
Press the MENU button to end the menu mode.
NOTE
This adjustment is available only when the automatic time
adjustment is set to off. (page 23)
Display and setting:
Calendar Mode
You can set the date formats of the calendar function.
1
Select the display "Clock Adjust" during the selecting function
in the menu system.
Display and setting:
2
Hold down either the 4 or ¢ button for two seconds or
more to enter the Manual time adjustment mode.
The time display will blink.
1
Select the display "Date Mode" during the selecting function in
the menu system.
2
Press the 4 and ¢ button to select the date format you
want to show in the display.
The sample of the date format for today is displayed.
3
4
• Adjusting the hours
Press the FM button to advance the hours, or press the AM
button to make the hours go back.
• Adjusting the minutes
Press the ¢ button to advance the minutes, or press the
4 button to make the minutes go back.
Press the MENU button to end the menu mode.
Memo Mode
You can input the text to be displayed and set the date when
that text will appear in the display with the calendar function.
Display and setting:
Calendar Adjustment
Adjust the date for the unit so that you can use the calendar
function.
1
Select the display "Memo Mode" during the selecting function
in the menu mode.
— 22 —
NOTE
2
3
4
Hold down either the 4 or ¢ button for two seconds or
more to enter the Memo mode.
• The text you selected automatically appears on the date you set
when the unit’s power is first turned on. (Calendar function)
Pressing the CLK button for one second or more scrolls the
display once, regardless of the text scroll setting.
Pressing a button other than the CLK button will cause the text
to disappear from the display.
• You can enter up to 32 characters for each text.
• The calendar function can be set up to 30 cases.
• To delete the date and text setting, set both the month and day
of the date to "00" or set all of the text to blanks.
The date display will blink.
Selecting the set of the date and text to be displayed
Press the FM and AM button.
If you want to input a new text, select the blank display.
Entering the month or day setting mode
Press the 4 and ¢ button to enter the month or day
setting mode.
The month display will blink enter the month setting mode, the
day display will blink enter the day setting mode.
5
6
Changing the month or day
Press the FM and AM button.
Automatic Time Adjustment
Entering the text input mode
With automatic time adjustment, you can set the clock time
automatically according to time data sent from RDS stations
(after receiving RDS signals for several minutes). You can also
set the time manually if the automatic time adjustment
function is turned off. The factory default is automatic time
adjustment.
Press the ¢ button to enter the text input mode.
The cursor blinks in the position where character input can be
made.
7
Inputting / Changing the text
• Moving the cursor
Press the 4 and ¢ button.
• Changing the type of characters
Press the TI button.
Each time the button is pressed, the type of characters
switches as follows.
Display and setting:
"SYNC ON" : Automatic time adjustment
"SYNC OFF" : Manual time adjustment
Adjusting Time Automatically:
Tune into an RDS station for 3 or 4 minutes.
The time adjusts automatically to the correct local time.
Alphabet (upper case): A ~ Z
NOTE
Alphabet (lower case): a ~ z
The time is not adjusted when the RDS station you are tuned to
is not transmitting a time signal. Choose another RDS station in
such a case.
Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]
Special characters: á
à
é
è
í
ì
ó
ò
ú
ù
Ñ
ë
î
ï
ô
ö
û
ü
ñ
ç
©
Æ
›
• Selecting the character
Press the FM and AM button.
8
Press the MENU button to end the menu mode.
— 23 —
Menu settings
Disabled System Indicator (DSI)
A red indicator blinks on the unit after the faceplate is
removed, warning potential thieves. The factory default for this
function is "ON".
ec4/dB (Sound Coordinate system)
When this system is set to on, the sound coordinate factors
(Bass frequency, Bass quality, Bass extension, and Treble
frequency) appear during the audio control mode.
Egnlish
Display and setting:
Display and setting:
"DSI ON" : The disabled system indicator is on.
"DSI OFF" : The disabled system indicator is off.
"ec4/dB set ON" : The sound coordinate factors appear and can
be adjusted.
"ec4/dB set OFF" : The sound coordinate factors are not
appeared.
Selectable Illumination
You can switch the colour of the button illumination between
News Bulletin Function
green and red.
with PTY News Timeout Setting
Display and setting:
You can arrange to have news bulletins interrupt your current
listening source, including other radio stations. When the
News Bulletin function is on, the PTY News Timeout setting
allows you to set the interval during which further news
interruption cannot take place. You can adjust the PTY news
interruption period from 10 to 90 minutes for each journey.
"Color Green" : The colour of the illumination is green.
"Color Red" : The colour of the illumination is red.
Contrast Adjustment
This adjustment permits easy viewing of the display.
Display and setting:
"NEWS OFF/ 00min/ 10min/ 20min/ 30min/ 40min/ 50min/
60min/ 70min/ 80min/ 90min"
(min= minutes)
Display and setting:
: When you select the news interruption timeout interval, the
News function turns on and the NEWS indicator lights up.
When a news bulletin is received, "NEWS" will be displayed
and reception will begin at the preset volume.
"Contrast 0" – "Contrast 10"
NOTE
The initial setting value is "5" .
NOTE
• If you choose the "20min" setting, further news bulletins will not
be received for 20 minutes once the first news bulletin is
received.
• This function is only available if the desired station sends PTY-
code for news bulletin or belongs to <Enhanced Other
Network>-Network sending PTY-code for news bulletin.
• If you turn on the news bulletin function in the MW/LW band,
the band is switched automatically to the FM band.
However, the MW/LW band is not returned to when you turn
off the function.
Switching Graphic Display
You can turn the graphic display on and off.
The initial setting is ON.
Display and setting:
"Graphic ON" : The graphic display is on
"Graphic OFF" : The graphic display is off.
— 24 —
NOTE
Local Seek Function
• When the AF function is turned on whilst auto memory entry
takes place, only RDS stations (i.e., stations with RDS
capability) are stored. RDS stations that have been preset for
FM1 cannot also be preset in FM2 or FM3.
• When the local seek function is turned whilst auto memory
entry takes place, stations with poor reception are not stored.
• When the Traffic Information function is on , only the local
traffic information station frequency will be stored.
With the local seek function turned on, auto seek tuning skips
stations with relatively poor reception.
Display and setting:
"Local.S ON" : The local seek function is on.
"Local.S OFF" : The local seek function is off.
Cancelling Auto Memory Entry During Its Operation:
Press the MENU button whilst auto memory entry is taking
place to stop the process.
Selecting Tuning Mode
You can choose from three tuning modes: auto seek, preset
station seek, and manual. The "AUTO 1" indicator lights up
when auto seek tuning is selected, and the "AUTO 2" indicator
lights when preset station seek tuning is selected.
Recalling a Preset Station:
Press the preset station button (#1-6) for the desired station.
The number of the recalled station is displayed.
Display and setting:
"Auto 1" : Auto seek tuning mode
"Auto 2" : Preset station seek tuning mode
"Manual" : Manual tuning mode
AF (Alternative Frequency) Function
When poor reception is experienced, automatically switch to
another frequency broadcasting the same programme in the
same RDS network with better reception.
The ™ indicator lights up when the AF function is turned
on.
Auto Memory Entry
You can automatically store all the receivable frequencies in
the band currently being listened to, and then recall them with
the touch of a button later. This function is especially useful
when you are travelling and do not know what stations are
available. Up to 6 frequencies can be stored this way.
Display and setting:
"AF ON" : The AF function is on.
"AF OFF" : The AF function is off.
NOTE
Display and setting:
• When no other stations with stronger reception are available for
the same programme in the RDS network, you may hear the
incoming broadcast in bits and snatches. Turn off the AF
function in such a case.
• The AF function can be turned on or off even when the standby
mode has been turned on. If the power is on, the AF function
tunes in to stations that offer good reception.
1
Select the display "Auto-Memory" during the selecting function
in the menu system.
2
Hold down either the 4 or ¢ button for two seconds or
more to start auto memory function.
The numbers of the preset station buttons showed in order.
When all the stations in a certain band are stored in the preset
memory, the auto memory entry stops. The tuner then plays
the last station received.
— 25 —
Menu settings
Restricting RDS Region (Region Restrict Function)
Text Scroll
You can choose whether or not to restrict the RDS channels,
received with the AF function for a particular network, to a
specific region. When the Region Restrict Function is on, the
region is restricted.
This function permits the CD text, MD title, and Radio text to
be scrolled and the entire text to be displayed. Switching
Switching between manual scrolling and automatic scrolling is
permitted. The factory default is manual scrolling.
Egnlish
Display and setting:
Display and setting:
"Regional ON" : The Region Restrict Function is on.
"Regional OFF" : The Region Restrict Function is off.
"Scroll Auto" : Automatic scrolling
"Scroll Manu" : Manual scrolling
NOTE
Sometimes stations in the same network broadcast different
programmes or use different programme service names.
Auto TP Seek Function
When the TI function is on and poor reception conditions are
experienced when listening to a traffic information station,
another traffic information station with better reception will be
searched for automatically. This function is on, when unit is
first powered on.
Display and setting:
"ATPS ON" : The Auto TP Seek Function is on.
If the traffic information station you are tuned to
experiences poor reception, this function
automatically seeks another TP station.
"ATPS OFF" : The Auto TP Seek Function is off.
Monaural Reception
When poor stereo reception is experienced, this function will
reduce noise and improve listening conditions.
Display and setting:
"Mono ON" : The monaural reception is on.
"Mono OFF" : The monaural reception is off.
— 26 —
Accessories
External view
Number of items
2CAUTION
• If your car is not prepared for this special connection-system,
consult your Kenwood dealer.
1
..........................................1
• Only use antenna conversion adapters (ISO-JASO) when the
antenna cord has an ISO plug.
• Make sure that all cable connections are securely made by
inserting jacks until they lock completely.
..........................................2
..........................................1
2
3
• If your vehicle's ignition does not have an ACC position, or if
the ignition cable is connected to a power source with constant
voltage such as a battery cable, the power will not be linked
with the ignition (i.e., it will not turn on and off along with the
ignition). If you want to link the unit's power with the ignition,
connect the ignition cable to a power source that can be turned
on and off with the ignition key.
2CAUTION
• If the fuse blows, first make sure that the cables have not
caused a short circuit, then replace the old fuse with one with
the same rating.
• Do not let unconnected cables or terminals touch metal on the
car or anything else conducting electricity. To prevent short
circuits, also do not remove the caps on the ends of the
unconnected cables or the terminals.
• Connect the speaker cables correctly to the terminals to which
they correspond. The unit may receive damage or fail to work if
you share the - cables and/or ground them to any metal part
in the car.
• After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
• Insulate unconnected cables with vinyl tape or other similar
material.
The use of any accessories except for those provided might
result in damage to the unit. Make sure only to use the
accessories shipped with the unit, as shown above.
Installation Procedure
1. To prevent short circuits, remove the key from the ignition and
disconnect the -terminal of the battery.
2. Make the proper input and output cable connections for each
unit.
3. Connect the cable on the wiring harness.
4. Take Connector B on the wiring harness and connect it to the
speaker connector in your vehicle.
5. Take Connector A on the wiring harness and connect it to the
external power connector on your vehicle.
• Some disc changers need conversion cables for connection.
See the section on "Safety Precautions" for details.
• If the console has a lid, make sure to install the unit so that the
faceplate does not hit the lid when closing and opening.
• Mount the unit so that the mounting angle is 30° or less.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
— 27 —
Connecting Cables to Terminals
Antenna Cord (ISO)
Fuse (10A)
Egnlish
Rear left
output (White)
Antenna Conversion Adaptor (ISO–JASO) (Accessory3)
FM/AM antenna
input
Rear right
output (Red)
KENWOOD disc changer control input
NOTE
To connect the Disc changer,
consult your Disc changer manual.
Wiring harness
(Accessory1)
Connector Function Guide
Pin Numbers for
ISO Connectors
External
Power
Connector
Cable Colour
Functions
TEL mute cable (Brown)
Connect to the terminal that
is grounded when either the
telephone rings or during
conversation.
TEL MUTE
Yellow
Blue/White
Battery
Power Control
NOTE
A–4
A–5
To connect the KENWOOD
navigation system, consult
your navigation manual.
Battery cable (Yellow)
Red
Black
Ignition (ACC)
Earth (Ground)
Connection
If no connections are made,
do not let the cable come
out from the tab.
A–7
A–8
Ignition cable (Red)
Speaker
Connector
B–1
Power control/ Motor
antenna control cable
(Blue/White)
P.CONT
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Connect either to the power
control terminal when using
the optional power amplifier,
or to the antenna control
terminal in the vehicle.
A–7 Pin (Red)
ANT.CONT
B–2
B–3
B–4
B–5
B–6
B–7
B–8
A–4 Pin (Yellow)
8
7
6
5
4
3
2
1
Connector A
Connector B
8
7
6
5
4
3
2
1
Green/Black
— 28 —
Connecting Cables to Terminals
Installation
■
Installation
2WARNING
Connecting the ISO Connector (see p.28)
The pin arrangement for the ISO connectors depends on the
type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
The default connection for the wiring harness is described in 1
below. If the ISO connector pins are set as described in 2 or 3,
make the connection as illustrated.
Firewall or metal support
Screw (M4X8)
(commercially
available)
1 (Default setting) The A-7 pin (red) of the vehicle's ISO
connector is linked with the ignition, and the A-4 pin (yellow)
is connected to the constant power supply.
Unit
Vehicle
A–7 Pin (Red)
Bend the tabs of the
mounting sleeve
with a screwdriver or
similar utensil and
attach it in place.
Ignition cable (Red)
Self-tapping
screw
(commercially
available)
Battery cable (Yellow)
A–4 Pin (Yellow)
Metal mounting
strap
(commercially
available)
2 The A-7 pin (red) of the vehicle's ISO connector is connected
to the constant power supply, and the A-4 pin (yellow) is
linked to the ignition.
NOTE
Unit
Vehicle
Make sure that the unit is installed securely in place. If the unit
is unstable, it may malfunction (eg, the sound may skip).
Ignition cable (Red)
A–7 Pin (Red)
Battery cable (Yellow)
A–4 Pin (Yellow)
3 The A-7 pin (red) of the vehicle's ISO connector is not
connected to anything, whilst the A-4 pin (yellow) is
connected to the constant power supply (or both the A-7 (red)
and A-4 (yellow) pins are connected to the constant power
supply).
Unit
Vehicle
Connect to a power source that can
be turned on and off with the ignition
key.
Ignition cable (Red)
Battery cable (Yellow)
A–4 Pin (Yellow)
— 29 —
Installation
■
■
Removing the hard rubber frame
Removing the Unit
1
Refer to the section “Removing the hard rubber frame” and
then remove the hard rubber frame.
1
Engage the catch pins on the removal tool and remove the
two locks on the lower level.
Lower the frame and pull it forward as shown in the figure.
2
3
Remove the screw (M4×8) on the back panel.
Egnlish
Insert the two removal tools deeply into the slots on each
side, as shown.
Catch
Lock
Catch facing up
Screw (M4X8)
(commercially
available)
Accessory2 Removal tool
2
When the lower level is removed, remove the upper two
locations.
Accessory2 Removal tool
4
Lower the removal tool
toward the bottom, and
pull out the unit halfway
whilst pressing towards the
inside.
2CAUTION
Be careful to avoid injury from the catch pins on the removal
tool.
NOTE
5
Pull the unit all the way out
with your hands, being
careful not to drop it.
The frame can be removed from the top side in the same
manner.
— 30 —
Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The power does not turn on.
The fuse has blown.
After checking for short circuits in the cables, replace
the fuse with one having the same rating.
No ACC position on vehicle ignition.
The Attenuator function is turned on.
Connect the same cable to the ignition as the battery cable.
Turn off the Attenuator function.
No sound can be heard, or the
volume is low.
The fader and/or balance settings are set all the way to
one side.
Reset the fader and/or balance settings.
The input/output cables or wiring harness are connected
incorrectly.
Reconnect the input/output cables and/or the wiring
harness correctly. See the section on "Connecting
Cables to Terminals".
The value of “V OFFSET” is low.
Increase the value of “V OFFSET”.
Nothing happens when the
buttons are pressed.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see page 4).
A speaker cable may be pinched by a screw in the car.
The speakers are not wired correctly.
Check the speaker wiring.
The sound quality is poor or
distorted.
Reconnect the speaker cables so that each output
terminal is connected to a different speaker.
Radio reception is poor.
The car antenna is not extended.
Pull out the antenna all the way.
The antenna control cable is not connected.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The memory is erased when
the ignition is turned off.
The battery cable has not been connected to the proper
terminal.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The ignition and battery cable are incorrectly connected.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The TEL mute function does
not work.
The TEL mute cable is not connected properly.
Connect the cable correctly, referring to the section on
"Connecting Cables to Terminals".
The TEL mute function turns
on even though the TEL mute
cable is not connected.
The TEL mute cable is touching a metal part of the car.
Pull the TEL mute cable away from the metal part of the
car.
— 31 —
Troubleshooting Guide
MD/External disc control mode
PROBLEM
POSSIBLE CAUSE
SOLUTION
The MD cannot be inserted.
The MD does not load.
There is already an MD loaded.
Eject the currently loaded MD and then load the new one.
Insert the MD in the proper orientation.
Egnlish
The insertion orientation of the MD is incorrect or the MD
is upside down.
The MD loads but soon comes
out again.
Nothing is recorded on the MD.
Replace the MD with one that is recorded.
Adjust to an angle of less than 30°.
The sound skips.
The mounting angle exceeds 30°.
The mounting is unstable.
Fix the unit securely. When the sound skips at the same
portion even when the car is stopped, the problem lies
with the MD.
There is noise during playback.
The MD is soiled with dust or dirt.
If another MD is played back and there is no problem,
then the problem is due to the sound quality of the MD
itself.
The disc control mode cannot
be selected.
No cable has been connected to the disc changer input
terminal on the unit.
Connect the cable to the disc changer input terminal on
the unit.
The specified disc does not
play, but another one plays
instead.
The specified CD is very dirty.
Clean the CD.
The CD is upside-down.
Load the CD with the labelled side up.
The disc is loaded in a different slot from that specified.
Eject the disc magazine and check the number for the
specified disc.
The disc is severely scratched.
Try another disc instead.
— 32 —
PROBLEM
POSSIBLE CAUSE
Something is touching the disc changer.
The CD is scratched or dirty.
SOLUTION
The sound skips.
Remove whatever is touching it.
If skipping happens at the same place when the car is
stopped, something is wrong with the CD. Clean the CD.
The display shows that the
changer is being played, but no
sound can be heard.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit (see page 4).
The specified track does not
play.
Random play or magazine random play has been
selected.
Turn off the random play or magazine random play
function.
Track repeat, disc repeat, track
scan, disc scan, random play,
and magazine random play
start by themselves.
The setting is not cancelled.
The settings for these functions remain on until the
setting to off or the disc ejected, even if the power is
turned off or the source changed.
If the following situations, consult your nearest service centre:
• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer
Mode.
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered
when switching modes.
— 33 —
Troubleshooting Guide
The following messages are displayed when certain problems are occurring in your system. Take the
recommended actions.
No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.
EJECT
]
Load the disc magazine properly.
No CD in the unit.
Egnlish
]
Insert the CD.
No disc has been loaded in the disc magazine.
NO DISC
E-04
]
Load a disc into the disc magazine.
No disc has been loaded in the disc magazine.
]
Load a disc into the disc magazine.
The CD is very dirty. The CD is upside-down. The CD is scratched a lot.
]
Clean the CD and load it correctly.
Nothing has been recorded on the MD.
BLANK
No tracks are recorded on the MD, although it has a title.
NO TRACK
NO PANEL
The faceplate of the slave unit being connected to this unit has been removed.
]
Replace it.
The unit is malfunctioning for some reason.
E-77
E-99
]
Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.
Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.
]
Check the disc magazine. And then, press the reset button on the unit.
If the "E- 99" code does not disappear, consult your nearest service center.
The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),
stopping all operation.
HOLD
]
Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),
the disc starts playing again.
The MD player section is not operating properly.
]
Reinsert the MD. If the MD cannot be ejected or the display continues to flash even when the MD has been properly
reinserted, please switch off the power and consult your nearest service centre.
IN
— 34 —
Specifications
Specifications subject to change without notice.
FM tuner section
Audio section
Frequency range (50 kHz Space)..............87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB) .................................0.7 µV/75 Ω
Quieting Sensitivity (S/N = 46dB) ..............................1.6 µV/75 Ω
Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz
Signal to Noise ratio (MONO)..............................................65 dB
Selectivity (DIN) ( 400 kHz) ............................................ ≥ 80 dB
Stereo separation (1 kHz) ....................................................35 dB
Maximum output power.................................................45 W × 4
Output power (DIN 45324, +B=14.4 V)..........................28 W × 4
Tone action
Bass: ...........................................................100 Hz 10 dB
Treble: .........................................................10 kHz 10 dB
Preout level / load ...............................1800 mV / 10 kΩ (MD/CD)
Preout Impedance............................................................≤ 600 Ω
MW tuner section
General
Frequency range (9 kHz Space).....................531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB) ...........................................25 µV
Operating voltage .............................14.4 V (11 – 16 V allowable)
Current consumption.............................................................10 A
Installation size (W × H × D) ..........................182 × 53 × 160 mm
Weight...............................................................................1400 g
LW tuner section
Frequency range .............................................153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB) ...........................................45 µV
MD player section
Laser diode ..........................................GaAlAs (λ=760 – 800 nm)
Digital filter (D/A) .....................................8 Times Over Sampling
D/A Converter .......................................................................1 Bit
Frequency response ( 2 dB).................................20 Hz – 20 kHz
Total harmonic distortion (1 kHz).......................................0.03 %
Signal to Noise ratio ................................................90 dB (1 kHz)
Dynamic range ....................................................................90 dB
Channel separation..............................................................85 dB
Spindle speed........................................................400 – 900 rpm
Wow & Flutter........................................Below Measurable Limit
— 35 —
|